ope体育

Kangyue dust collector, spray tower dust collector - spray tower dust collector

Mobile phone station | Enterprise trends | Website map
Service hotline:
fifteen billion thirty million seven hundred and ninety-six thousand eight hundred and ninety-one
Hot Tags: Bag filter | Single dust collector | Pulse precipitator | Cyclone dust collector | Dust bag | Dust removal framework | Electromagnetic pulse valve |
 Dust remover spray tower dust collector

Spray tower dust collector

Spray tower dust collector is a kind of dust remover developed by filling type dust collector. The filling layer is not a static filling material, but a number of light balls which are tossed up and down by the impact of air flow. The main part of spray tower dust collector is composed of sieve plate and small ball,
Place of Origin: Hebei Province > Botou City
supplier: Botou Kangyue environmental protection Co., Ltd
 Click here to send me a message
Hotline: 0317-8346823 8295600

Detailed introduction of spray tower dust collector

Spray tower a duster It's filled in a duster A dust remover developed. The filling layer is not a static filling material, but a number of light balls which are tossed up and down by the impact of air flow. The sphere may be one or two or three or even several sections. The upper and lower sieve plates play a supporting role. Usually, the upper sieve plate of a section of ball layer is the lower sieve plate of upper segment ball layer. Sieve plate can be orifice plate or grid bar. The upper part of the spherical layer is equipped with a liquid spraying device, so that the spherical surface is turned_ It is wetted to form a gas-liquid contact mass transfer interface. Under the washing of spray liquid, the interface is constantly updated, which can effectively carry out mass transfer absorption and dust removal.

Spray tower Structure of dust collector

Spray tower The main part of the dust collector is composed of sieve plate and small ball,

one Spray tower Sieve plate of dust collector

one The upper and lower sieve plates (or bars) of the ball layer. The aperture of sieve plate or the clearance of grid bar shall not be greater than two thirds of the diameter of the ball, so as to prevent the ball from being stuck. The opening rate is generally at 45%~60% If it is too small, it will increase the resistance due to too much liquid blocking. The screen plate or grid bar can make the air flow evenly distributed, and also can enhance the gas-liquid contact, which is conducive to mass transfer. The upper plate mainly prevents the small balls from being carried away by the air flow, so it is also possible to use textile mesh, such as the net made of plastic rope or nylon wire.

2.  Before the distance between the upper and lower sieve plates determines the distance between the upper and lower sieve plates_ First determine the height of the sphere stack H1 If the sphere layer is too high, the slug flow and bias flow will occur, which will affect the purification efficiency and increase the resistance of the tower. For_ Sufficient mass transfer time can be achieved by increasing the number of layers.

(2) Spray tower a duster Diameter( D )And ball diameter( d h )The ratio should be greater than ten The size of the ball has an effect on heat and mass transfer. The specific surface area of the ball is large, the liquid volume in the bed is large, and the interface between gas and liquid is also large. However, for the same material and wall thickness, the pile density of small balls is higher, so the resistance of the balls with the same stacking height is also slightly larger. The material requirements for the packing ball are as follows:_ In addition, it is not soluble in the treated medium and has good wear resistance_ It has the advantages of low density and easy processing.

Browse more about Spray tower dust collector Content of

contact information

Botou Kangyue environmental protection limited company
Address: Fuchen Development Zone, Botou City
Tel: 0317-8295600
Fax: 0317-8285600
Mobile phone: 15030796891
Email: btkscc @ 126.com
 
Home page | Central products | Industrial duster | technical information | Enterprise album | Information Center | after-sale service | Company profile | Enterprise qualification | contact information | Google Maps
Company name: Botou Kangyue environmental protection Co., Ltd. Company Address: huangtun, Siying Township, Botou City postcode: 062151 Tel: 0317-8346823 8295600 Fax: 0317-8285600
Mobile phone: 15030796891 13831773535 website: http://cms007.com Email: btkscc @ 126.com
Botou Kangyue environmental protection 2011 (c) all rights reserved Jiicp no.15008741-1  

Jihuang Gongwang Anbei no.13098102000341

Powerby: supei.net.com website construction: China Science and technology Sifang